⚠️ High Alert Medication

Vasopressin Infusion

Syringe pump continuous infusion preparation (1 unit/mL), hemodynamic titration, and extravasation surveillance protocol.

Syringe Pump Infusion Preparation (Standard Concentration)

Ampoule Presentation 1 mL ampoule (20 units/mL of vasopressin)
Vasopressin Dose 40 units (2 mL = two 1 mL ampoules)
Compatible Diluent 38 mL of 0.9% Sodium Chloride (NS) or D5W
Final Syringe Volume 40 mL
Final Concentration 1 unit/mL
Stability 24 hours at room temperature

Materials Required

  • Vasopressin ampoules 20 units/mL (1 mL) × 2
  • 60 mL Luer-lock syringe
  • 0.9% Sodium Chloride (NS) or D5W
  • Sterile drawing-up needle / filter needle
  • Dedicated syringe pump infusion label
  • Extension line (100 cm)
  • Alcohol chlorhexidine swabs

Preparation Procedure (Aseptic Non-Touch Technique)

  1. Verification: Verify the written physician order, patient identity, body weight, and clinical indication.
  2. Hand Hygiene: Perform thorough hand hygiene and clean preparation workspace.
  3. Ampoule Check: Check each vasopressin ampoule for:
    • Correct drug and strength, vasopressin (20 units/mL)
    • Expiry date
    • Container integrity, clarity, and absence of precipitate or discoloration
  4. Withdrawal: Open two ampoules of vasopressin. Withdraw 1 mL from each ampoule into a 60 mL Luer-lock syringe (Total vasopressin drawn: 2 mL = 40 units vasopressin).
  5. Dilution: Add 38 mL of 0.9% Sodium Chloride or D5W to a final volume of 40 mL.
  6. Mixing: Gently invert the syringe several times to ensure uniform mixing.
  7. Visual Inspection: Inspect solution to ensure it is clear, colorless, and free of visible particles.
  8. Labeling & Dual Verification: Apply infusion label and obtain an independent double-check by another registered nurse.
  9. Syringe Pump Setup: Prime the extension set, install into the syringe pump, and shield from excessive ambient light.

🔒 Lumen Policy: vasopressin is physically and chemically incompatible with numerous medications. It must be infused via a dedicated central venous catheter lumen whenever possible.

⚠️ Peripheral Administration: In an emergency situation, vasopressin may be infused peripherally for short-term bridging use only, with frequent site monitoring for extravasation.

Administration & Titration

Recommended Dosing Parameters

  • Administration Route: Administer via syringe pump; dedicated central line lumen preferred.
  • Recommended Starting Dose: 0.01 to 0.03 units/min (titrate infusion to achieve desired hemodynamic result).
  • ICU Titration Range: 0.01 to 0.06 units/min.
  • High-Dose Range: Higher doses may be used depending on clinical condition under direct intensivist supervision.
  • Syringe Continuity: Do not allow the infusion to run out. A syringe can be made up to a maximum of 1 hour in advance and labelled clearly with contents and expiry.
  • Discard Policy: Discard 24 hours after preparation or earlier if the solution becomes discoloured, cloudy, or contaminated.

Hemodynamic Monitoring Requirements

  • Monitor arterial blood pressure continuously (invasive arterial line preferred).
  • Monitor heart rate and continuous ECG rhythm.
  • Monitor for peripheral tissue ischemia or necrosis.
  • Assess end-organ perfusion markers (urine output, mental status, peripheral pulse volume, serum lactate).

Extravasation Surveillance & Response Protocol

Extravasation of potent vasopressors causes severe local vasoconstriction leading to ischemic sloughing and necrosis.

Normal Infusion Site

  • No cutaneous blanching
  • No local swelling
  • No pain, burning, or stinging
  • No tissue discolouration

Extravasation Suspected:

  1. STOP infusion immediately (do not flush line).
  2. Notify clinician promptly.
  3. Aspirate residual drug through the cannula if possible, then remove catheter.
  4. Document event in patient clinical record.

© criticalcareinsights.com. All rights reserved. For clinical reference and educational use only.